Z Microsystems GLIDER 20 Uživatelský manuál

Doc# 27-0006UM Issued 11/00 Rev 1.0Z MicrosystemsFIELD-READYZ MicrosystemsUser ManualFIELD-READYGLIDER20

Doc# 27-0006UM Issued 11/00 Rev 1.0FINAL ADJUSTMENTSSlide the Glider partiallyout.Use a flathead screw-driver to slightly movethe Z-Locks in toward

Doc# 27-0006UM Issued 11/00 Rev 1.011WARNING: Be sure all electricalpower to the cabinet isoff before connectingany of the cables.WARNING: There i

Doc# 27-0006UM Issued 11/00 Rev 1.0VERY IMPORTANT.Hold the top of thedisplay in the verticalposition while rotatingthe latch clockwise tothe locked

Doc# 27-0006UM Issued 11/00 Rev 1.0The display can berotated clockwise toangled positions.The display can also bemoved into the horizon-tal positio

Doc# 27-0006UM Issued 11/00 Rev 1.0Protector Removal14The display protector is intended to protect the surface of the screen fromdamage while in tra

Doc# 27-0006UM Issued 11/00 Rev 1.0OperationCONNECTING CABLESTURN ON POWERNOTE: Connecting to non-standardsystems will require anadapter. To ob

Doc# 27-0006UM Issued 11/00 Rev 1.0Monitor AdjustmentsINITIAL SETUP AND ADJUSTMENTSThe Glider features pushbuttoncontrols on the lower front of t

Doc# 27-0006UM Issued 11/00 Rev 1.017This section explains how to use theGlider control buttons to adjust theclarity of the display and imagepositio

Doc# 27-0006UM Issued 11/00 Rev 1.0Monitor Adjustments18V Pos Moves the screen image up ordown.Clock The Clock  controlsmove the

Doc# 27-0006UM Issued 11/00 Rev 1.019The Glider can store screen settingsfor multiple resolutions, which isespecially useful when it is used witha g

Doc# 27-0006UM Issued 11/00 Rev 1.01. Use the power andvideo cables suppliedwith the Glider to helpprevent interferencewith radio andtelevision rece

Doc# 27-0006UM Issued 11/00 Rev 1.020Monitor AdjustmentsStep 1: Power UpAfter the installation instructions havebeen followed: Turn on power

Doc# 27-0006UM Issued 11/00 Rev 1.021Step 3: Adjust HorizontalWidthThis is the critical step to ensure acrisp screen image. For a Sharpdisplay

Doc# 27-0006UM Issued 11/00 Rev 1.0Monitor Adjustments22Step 4: Adjust HorizontalPositionPress the SELECT button until the HPos indicator i

Doc# 27-0006UM Issued 11/00 Rev 1.023To adjust the screen for the bestpossible display, try the following: Press the and buttonsuntil

Doc# 27-0006UM Issued 11/00 Rev 1.024Display Head RemovalTo remove the Glider display head, follow these steps:On the back of thedisplay, press them

Doc# 27-0006UM Issued 11/00 Rev 1.025CLEAN MONITOR Gently wipe the covers and thescreen with a soft cloth. Remove finger marks and greasewith a

Doc# 27-0006UM Issued 11/00 Rev 1.0CLOSE GLIDERDisplay StowageTilt the display headback towards the rear ofthe rack all the way tothe horizontal p

Doc# 27-0006UM Issued 11/00 Rev 1.0Lower the pivot latchinto its recepticle.Slide the Glider into theframe until it snaps intothe closed, secureposi

Doc# 27-0006UM Issued 11/00 Rev 1.028TroubleshootingNO IMAGE ON DISPLAY  Flip the power switch to on. Thecircle should be down. Connect the

Doc# 27-0006UM Issued 11/00 Rev 1.029FEATURES Large Display Area Multi-Scan/Sync Capability Wide Viewing Angle Small Package Outline Full Color

Doc# 27-0006UM Issued 11/00 Rev 1.0STARTING POINT 4Shipment Contents 4User Manual 4System Requirements 4Product Description 5Tools Required 6Preca

Doc# 27-0006UM Issued 11/00 Rev 1.0Specifications30PHYSICAL SPECIFICATIONSDisplay Dimensions Height 16.7 in (42.4 cm) Width 20.0 in (50.8 cm

Doc# 27-0006UM Issued 11/00 Rev 1.031DISPLAY SPECIFICATIONSDisplay Area Horizontal 15.7 in (39.9 cm) Vertical 12.6 in (32.0 cm) Diagonal

Doc# 27-0006UM Issued 11/00 Rev 1.0Z Microsystems has achieved full Y2K Compliance.In late 1997, the companys senior management assigned a Y2K Proj

Doc# 27-0006UM Issued 11/00 Rev 1.0NOTE: If possible, stay by thecomputer. The Z MicrosystemsTechnical Support Representa-tive may wish to go thro

Doc# 27-0006UM Issued 11/00 Rev 1.0If the Z Microsystems TechnicalSupport Engineer determines that theproduct needs to be replaced, aCustomer Servic

Doc# 27-0006UM Issued 11/00 Rev 1.0Z Microsystems, Inc.5945 Pacific Center Blvd., Suite 509San Diego, CA 92121Phone: (858) 657-1000Fax; (858) 657-

Doc# 27-0006UM Issued 11/00 Rev 1.0The User Manual comes in twoformats: printed hardcopy or CD-ROM. This Manual is also availableon the Z Microsyst

Doc# 27-0006UM Issued 11/00 Rev 1.0PRODUCT DESCRIPTIONThe LCD displaycan quicklyswing up into areading position.5Starting PointThe Glider is anadv

Doc# 27-0006UM Issued 11/00 Rev 1.0TOOLS REQUIREDPRECAUTIONS Required Tools and Equipment. Flathead screwdriver with about10" shaft. Phill

Doc# 27-0006UM Issued 11/00 Rev 1.0SLIDE REMOVALWith the Glider laid ona workbench, pressdown to release the Z-Locks on each side ofthe front of th

Doc# 27-0006UM Issued 11/00 Rev 1.0Install SlidesAt the back of thecabinest frame, tightenthe slide mounts to thecabinet frame.Make sure to hold the

Doc# 27-0006UM Issued 11/00 Rev 1.0Install Glider9INSTALL THE GLIDER IN CABINET FRAMEThe Glider slides shouldmove in and out easily.If not, ch